8th Floor, L&C Annex, 401 Church Street
Nashville, TN 37243-1551
1-800-734-3619 or email: email@example.com
TDEC's Self Disclosure Policy
Sample Request for Monetary Penalty Waiver
Compliance Advisory Panel
Emerg. Planning & Community Right to Know Act
Energy conservation and efficiency
Hazardous Air Pollutants list
Risk Mgt. Program - Clean Air Act Section 112(r)
Spill Prevention Control & Countermeasures Plan
NESHAP (MACT) standards by affected source category
Hot Mix Asphalt Plants
Processing and Roofing Products Manufacturing
Al, Cu, and Nonferrous Foundries
Ferroalloy Production Facilities
Metal Fabrication and Finishing
Plating and Polishing Paint
Paints and Allied Products Manufacturing
Surface Coating and Paint Stripping
Ready Mix Concrete
Reinforced Plastic Composites
Retail Gasoline Marketers
Risk Management Program
Storm Water Management
Construction: NPDES permit brochure
ECOS: Small Communities
**Federal Rules Affecting Paint Stripping, Autobody Refinishing, and Miscellaneous Surface Coating Operations at Area/Small Sources**
EPA 40 CFR Part 63 Subpart HHHHHH (6H)
( See rule )
Attention!! All changes in a facility's operation or submitted information must be logged by December 31st of that year. For each change, the logged information must include the following:
* date and time period of the change,
* a description of the nature of the change and
* the actions taken to correct the change.
The logged information must be submitted in an Annual Report to the appropriate air agencies by March 1st of the following year after the change(s).
No Changes to Report:
* January 1st, note this information in your records.
READ YOUR APC PERMIT
Your APC Permit may require your facility to report this information at a certain date.
Keep copies of all Notifications, Logs, and Reports availiable at the facility at least 5 years (read permits for actual required time and form keeping data).
A Notice of Compliance is due by March 11, 2011
Sources in Shelby, Davidson, Knox and Hamilton Counties check with your local air program (Contacts)
If you have not submitted a notification stating facility compliance with 6H, then you should do so by March 11, 2011. - See sample compliance notification.
For assistance or hard copies:
Contact the the Small Business Environmental Assistance Program’s at 1-800-734-3619 or by e-mail at BGSBEAP@tn.gov [Attention: Surface Coating]
On January 9, 2008, the U.S. Environmental Protection Agency published rules to reduce air toxics including methylene chloride and other hazardous air pollutants (HAPs) from surface coating operations at area sources. The final rule is the National Emission Standards for Hazardous Air Pollutants (NESHAP) for Paint Stripping and Miscellaneous Surface Coating Operations at Area Sources, 40 CFR Parte 63 Subpart HHHHHH (6H). See rule.
An Initial Notice was due January 11, 2010.
Area sources that conduct any of the following:
» Paint stripping operations that use methylene chloride for the removal of dried paint.
» Motor vehicle (Autobody) and mobile equipment spray coating operations
» Miscellaneous surface coating operations (All of the following must apply):
• Perform hand-held spray painting
• Spray paint metal, plastic or a combination of the two
• Use surface coating material that contain chromium, lead, manganese, nickel, or/and cadmium
What are the Rule’s Exemptions (please check-you could be exempt!)?
An area source is a source that does not have the potential to emit more than the following:
» 10 tons or more per year of a single HAP or
» 25 tons or more of a combination of one or more HAPS or
» 100 tons or more per year of a criteria pollutant
» Spray painting must be conducted in a booth
» Painters must use HVLP spray guns or equivalents
» All painters must complete a training course on proper spray gun use and maintenance
» Specific spray gun cleaning requirements
» Paint stripping operations must implement management practices that minimize emissions of methylene chloride
The Tennessee Technology Centers may offer hands on training classes required by the new air pollution control rule. Please visit http://www.tbr.edu/schools/default.aspx?id=2654 to find the location nearest you.
New Operations [started after September 17, 2007] (New)
» Must be in compliance with the new rules upon start-up
» Must submit an Initial Notification and Notification of Compliance Status no later than 180 days after initial start-up (Call 1800-734-3619 for additional new source information)
Existing Operations [started on or before September 17, 2007]
» Must submit an Initial Notification no later than January 11, 2010. See sample initial notification.
» Must be in compliance by January 10, 2011
» Must submit a Notification of Compliance Status on or before March 11, 2011. See sample compliance notification.
Sample Opt Out Petition - if applicable
» Initial Notice
» Compliance Notice
» Brief Autobody Rule Summary
» Brief Miscellaneous Surface Coating Rule Summary
» Brief Paint Stripping Rule Summary